RE14010C2D REV A Amana Air Conditioner Parts List

Leveling foot (dryer leveling leg)

The adjustable leveling leg is used to support and keep your dryer level. It also allows you to adjust the height of your dryer. You may need to replace the leveling leg if one becomes lost, the thread is stripped off, or it is noisy during operation. The leveling leg is almost 2” long, white in color, and made of plastic. There are four leveling legs used on the dryer, please order quantity needed as they are sold individually. This is a genuine OEM part.

Surface burner terminal block kit (terminal block)

This kit includes the female contact with wires, terminal block and mounting clip.

Refrigerator shelf frame with glass (refrigerator shelf)

Roller support tri-ring (tri ring)

The tri ring is used to hold the drum support rollers or the idler pulley onto the shaft. If your dryer will not tumble or is noisy, you may need to replace the tri ring. This is a genuine OEM part and is sold individually.

Crisper drawer (pan, crisper)

The crisper drawer is used for storing fruits and vegetables at a humidity level that will help them stay fresh longer. If the crisper drawer is damaged, you may need to replace it. This crisper drawer is made of clear plastic and measures 12.847" depth by 15.217" width by 6.93 height. This part is sold individually and does not come with the plastic faceplate on it. If your current crisper drawer has one, you will need to remove it and transfer it to the new crisper drawer. NOTE: As per the manufacturer, the crisper drawer has been updated from the original. A new crisper cover may need to be purchased for the drawer to work.

Retainer bar end cap - left or right side (cap shlf frt)

Sold individually.

Control knob (range surface burner knob)

This knob accepts a D-shaped shaft. Sold individually.

Drive belt - 51 inches long (sub 21352320)

This V-style drive belt is about 51-inch long and 3/8-inch wide. This part is made to slip onto the motor pulley to bring the basket up to the speed required. The belt encounters wear and tear over time. If your washer will not drain, spin, or agitate, you may need to replace your belt. It is recommended to disconnect the power to your washer before you start your repair. This V-style belt is a genuine OEM part.

Top burner igniter

This top burner igniter has a male spade terminal. It is used to create a spark that will light the gas and start the burner when the burner knob is depressed and turned. The mounting bracket is included with the igniter. If your element will not heat, will not start, or the gas igniter glows but will not light, you may need to replace the igniter. This is a genuine OEM part. It is recommended to disconnect the power to your range before you start your repair.

Torx screw (screw, valve)

7-18 x 3/4" - sold individually.

Front load washer door lock and switch assembly

Sealed burner cap with electrode (sub 12500099)

This burner cap assembly is sold with the spark electrode. Please note this part has been redesigned and no longer requires a gasket. Sold individually.

Defrost timer

This 120 volt, 60Hz defrost timer acts like a clock, continually advances and alternates between activating the cooling cycle and the defrost heater. If the refrigerator is too warm, freezer section too warm or freezer not defrosting you might need to replace the defrost timer. This is a genuine OEM part. Disconnect the power to the refrigerator before starting the repair.

Door cam - black (door closer, lower cam (sold individually, 2 recommended))

The refrigerator uses a set of cams to help with the closing of the doors and help to keep them in position. These cams are mounted around the door pivot point and are made up of a series of ridges and valleys to help keep the door in position. If your refrigerator uses a door closer, the door should shut all by itself. This part is black in color, made of plastic, and is sold individually. This is a genuine OEM part. Note: As per the manufacturer a new screw is needed to mount the door cam. This door cam is sold individually.

Door gasket (door gasket (black))

The dishwasher door gasket provides a water tight seal between the tub and the door, to keep water from leaking out of your dishwasher. If your dishwasher is leaking you may need to replace the door gasket. The door gasket can be installed by simply pressing it into the channel around the door. This black door gasket measures 66.5-inch L x 42.7-inch W x .445-inch, is made of rubber and is a genuine OEM part.